nixpkgs/nixos/doc/manual/configuration/kubernetes.xml
Vladimír Čunát 4c3ec0e325
nixos docs: run the formatting tool (no content change)
As documented in the docs themselves :-)
2019-03-22 14:44:11 +01:00

113 lines
5.2 KiB
XML

<chapter xmlns="http://docbook.org/ns/docbook"
xmlns:xlink="http://www.w3.org/1999/xlink"
xmlns:xi="http://www.w3.org/2001/XInclude"
version="5.0"
xml:id="sec-kubernetes">
<title>Kubernetes</title>
<para>
The NixOS Kubernetes module is a collective term for a handful of individual
submodules implementing the Kubernetes cluster components.
</para>
<para>
There are generally two ways of enabling Kubernetes on NixOS. One way is to
enable and configure cluster components appropriately by hand:
<programlisting>
services.kubernetes = {
apiserver.enable = true;
controllerManager.enable = true;
scheduler.enable = true;
addonManager.enable = true;
proxy.enable = true;
flannel.enable = true;
};
</programlisting>
Another way is to assign cluster roles ("master" and/or "node") to the host.
This enables apiserver, controllerManager, scheduler, addonManager,
kube-proxy and etcd:
<programlisting>
<xref linkend="opt-services.kubernetes.roles"/> = [ "master" ];
</programlisting>
While this will enable the kubelet and kube-proxy only:
<programlisting>
<xref linkend="opt-services.kubernetes.roles"/> = [ "node" ];
</programlisting>
Assigning both the master and node roles is usable if you want a single node
Kubernetes cluster for dev or testing purposes:
<programlisting>
<xref linkend="opt-services.kubernetes.roles"/> = [ "master" "node" ];
</programlisting>
Note: Assigning either role will also default both
<xref linkend="opt-services.kubernetes.flannel.enable"/> and
<xref linkend="opt-services.kubernetes.easyCerts"/> to true. This sets up
flannel as CNI and activates automatic PKI bootstrapping.
</para>
<para>
As of kubernetes 1.10.X it has been deprecated to open non-tls-enabled ports
on kubernetes components. Thus, from NixOS 19.03 all plain HTTP ports have
been disabled by default. While opening insecure ports is still possible, it
is recommended not to bind these to other interfaces than loopback. To
re-enable the insecure port on the apiserver, see options:
<xref linkend="opt-services.kubernetes.apiserver.insecurePort"/> and
<xref linkend="opt-services.kubernetes.apiserver.insecureBindAddress"/>
</para>
<note>
<para>
As of NixOS 19.03, it is mandatory to configure:
<xref linkend="opt-services.kubernetes.masterAddress"/>. The masterAddress
must be resolveable and routeable by all cluster nodes. In single node
clusters, this can be set to <literal>localhost</literal>.
</para>
</note>
<para>
Role-based access control (RBAC) authorization mode is enabled by default.
This means that anonymous requests to the apiserver secure port will
expectedly cause a permission denied error. All cluster components must
therefore be configured with x509 certificates for two-way tls communication.
The x509 certificate subject section determines the roles and permissions
granted by the apiserver to perform clusterwide or namespaced operations. See
also:
<link
xlink:href="https://kubernetes.io/docs/reference/access-authn-authz/rbac/">
Using RBAC Authorization</link>.
</para>
<para>
The NixOS kubernetes module provides an option for automatic certificate
bootstrapping and configuration,
<xref linkend="opt-services.kubernetes.easyCerts"/>. The PKI bootstrapping
process involves setting up a certificate authority (CA) daemon (cfssl) on
the kubernetes master node. cfssl generates a CA-cert for the cluster, and
uses the CA-cert for signing subordinate certs issued to each of the cluster
components. Subsequently, the certmgr daemon monitors active certificates and
renews them when needed. For single node Kubernetes clusters, setting
<xref linkend="opt-services.kubernetes.easyCerts"/> = true is sufficient and
no further action is required. For joining extra node machines to an existing
cluster on the other hand, establishing initial trust is mandatory.
</para>
<para>
To add new nodes to the cluster: On any (non-master) cluster node where
<xref linkend="opt-services.kubernetes.easyCerts"/> is enabled, the helper
script <literal>nixos-kubernetes-node-join</literal> is available on PATH.
Given a token on stdin, it will copy the token to the kubernetes secrets
directory and restart the certmgr service. As requested certificates are
issued, the script will restart kubernetes cluster components as needed for
them to pick up new keypairs.
</para>
<note>
<para>
Multi-master (HA) clusters are not supported by the easyCerts module.
</para>
</note>
<para>
In order to interact with an RBAC-enabled cluster as an administrator, one
needs to have cluster-admin privileges. By default, when easyCerts is
enabled, a cluster-admin kubeconfig file is generated and linked into
<literal>/etc/kubernetes/cluster-admin.kubeconfig</literal> as determined by
<xref linkend="opt-services.kubernetes.pki.etcClusterAdminKubeconfig"/>.
<literal>export KUBECONFIG=/etc/kubernetes/cluster-admin.kubeconfig</literal>
will make kubectl use this kubeconfig to access and authenticate the cluster.
The cluster-admin kubeconfig references an auto-generated keypair owned by
root. Thus, only root on the kubernetes master may obtain cluster-admin
rights by means of this file.
</para>
</chapter>